Micro 433 RF UHF Beacon tracker for lost RC models, pets, falconry, people, cars

Description

There are still delays to all destinations because of the impacts of CVID-19 on airline capacity and in-country delivery impacts.
Shipping time can up to 120 days! Especially to USA, Austrilia and etc.
If you not agree - please do not bid!
P.S. PayPal have 180 days buyers protection
This is
ExpertRC Beacon PRO pack
include:
1x UHF Beacon with Spring Antenna
1x UHF Beacon with Wire Antenna
1x MicroUSB Charger for LIR2032 battery
3x LIR2032 battery
With USB Cable options:
+1x USB Uart TTL Cable for programming (optional)
+3x cables for connecting
(optional)
If you need another antenna or something else, please contact first.
This tracking device was originally developed for find lost quadcopters/multicopter/plane RC models,
however it may also be used for other applications such as pets, birds, falconry, peoples, Cars, balloons, wild animals and many others.
It small but powerful- you'll hear your beacon up to 10-15 km in the air, and few kilometers on the ground via regular portable UHF radio/Walkie Talkie w stock antenna.
Quick video demo
https://youtu.be/1PBSFgBe2i0
It highly customizable- you can change almost anything in serial menu setting.
Delay start function accept any RC or FPV control/video band and not affected to 433MHz also.
Up to 4 hours delay start.
Delay between TX: 5-255 sec
3 tonality, each can set individually power/tonality/duration separate
Frequency range 430.550-436.925MHz / 430.550+(Ch*0.025) channel from 0 to 255
Modulation:  NFM D=5KHz
RF power: 100 mW to 0.01 mW
Power via VCC pin: 3-6,6v
!OR!
Power via battery port: 2.6-4.2v
Current consumption:  up to 75 mA on TX
You can use CR2032, CR2025 battery but you need to reduce the power settings.
Current consumption in sleep - 0.02 mA (depending on operating conditions)
Weight: ~6.3 grams (w battery) 3.6 grams- no battery
Dimensions~ 22 x 38 x 8 mm
!WARNING!
Do not connect battery in the wrong polarity! +battery only to + beacon or +USB charger!
Do not connect battery to battery port and power to VCC pin at the some time.
Do not power up without antenna!
Do not connect to VCC pin more then 6,6v!
Do not Short Circuit battery!
Do not set TX delay less then 5 seconds!
To configure setting of beacon you need:
1. connect
TX pin of usb cable to RX pin of Beacon
RX to TX
GND to GND
5v to VCC
Plug to USB port and install drivers for cp2102 if needed
Open serial terminal programme (Putty or else ) and connect to you COM
port and 9600 speed,
you will se
"HOLD M for menu"
Press and hold (up to 1 minutes depend of TX delay settings) BIG "M" and wait for mark
"Press ENTER to menu"
Then press Enter
you will see menu
1       29      Factory Calibrate FR. NOT CHANGE! /F92
2       101     Ch. N 0-255 (430.550+(0.025*N)) 255=436.925 /F101=433.075
3       5       Delay start MIN. 0-255 /F5
4       30       Delay between TX sec. 5-255 /F30
5       1       Increasing time sec. between TX 0-255 /F1
6       127     1s TX Power 0-127 /F127
7       15      2s TX Power 0-127 /F15
8       1       3s TX Power 0-127 /F1
9       19      1s Tone X / F19
10      100     1s Tone Y / F100
11      22      2s Tone X / F22
12      80      2s Tone Y / F80
13      37      3s Tone X / F37
14      50      3s Tone Y / F50
----------
input N, press Ent, input Val, press Ent
To change setting you need enter register №, press "Enter" ,then enter
value and press "Enter".
REG 1 - Factory Calibrate parameter- set on fabric, it little trim Frequency PLL, do not change it if you not sure!
REG 2 - Channel № - Set Frequency by formula (430.550+(0.025*N)), default value is 101, it is 433.075MHz
REG 3 - Delay start in Minutes, usually set you regular flight time, can be from 0-255
REG 4 - Delay between TX in seconds, can be from 0-255
REG 5 - Increasing time in seconds between TX, can be from 0-255, this add extra delay between TX, 30sec,31sec,32sec etc
REG 6 - First ton TX Power,can be from  0 to 127, default value is 127
REG 7 - Second ton TX Power,can be from  0 to 127, default value is 15
REG 8 - Fird ton TX Power,can be from  0 to 127, default value is 1
REG9-14 for duration and tone setting by formula FOR X;(TOGGLE; Delay Y)
do not change it if you not sure!
after setting you can press ENTER twice and Beacon rebooting with new setting
PLEASE PUT "+" battery to "+" mark of charger, otherwise battery can break down.
RED LED- Charging / BLUE LED- end charging or no battery.
Charging time up to 2 hours.